Skip to main content

The printer shows a message, what now?

Written by Jochem

If something is wrong with the printer, you see a printer icon with a red exclamation mark on the start screen. Tap it: the photobooth tells you what's wrong. Taking photos carries on as normal.

The DNP QW410 photo printer


​

Safety first

  • The print head inside is hot: don't touch it.

  • There's a sharp blade at the photo output and above the scrap tray: keep your fingers away.

  • Don't switch the printer off or take out the scrap tray while it's printing.

  • Never pull hard and never force the cover or the paper.


​

What's wrong?


​

The printer is off

  1. Switch the printer on with the button on the back.


​

The cover is open or the scrap tray is missing

  1. Close the printer cover.

  2. Push the scrap tray at the front all the way in.


​

The printer won't print without this tray. Is the tray full? Wait until the printer has finished printing, take it out, throw away the scraps and push it all the way back in.


​

Paper or ribbon has run out

Paper and ribbon belong together: always replace them together, with a new pack from the box. Leave the printer switched on while you change them.

  1. Only take the new roll out of its plastic, and the new ribbon out of its paper bag (gently tear it open), when you need them. Never put them loose on a table: dust causes streaks.

  2. Pull the lever on top of the printer towards you. The top cover opens.

  3. Take out the old ribbon.

  4. Hold the new ribbon with the thick roll towards you. Put the left side into the slot first.

  5. Then lower the right side until it clicks.

  6. Carefully turn the small roll until the ribbon is tight, without creases.

  7. Close the cover.

  8. At the front, take out the scrap tray and throw away the scraps. Watch out for the blade above it.

  9. Take out the paper holder and put it on a clean surface.

  10. Take off the old core and put the new roll on, tight against the holder.

  11. Put the holder back with the "PULL" label facing the same way as on the picture in the printer.

  12. Remove the seal from the paper. Hold the paper in place and turn the holder until the printer beeps.

  13. Put the scrap tray back and push it all the way in.

  14. The printer now feeds out 3 blank sheets. That's normal: throw them away. After that you can print again.


​

The paper is stuck

  1. Switch the printer off and on again with the button on the back. The blade then moves back.

  2. Is half a sheet hanging out of the printer? Gently take it out. This often solves the problem.

  3. Still stuck? Open the cover and take out the ribbon.

  4. Turn the paper holder back by hand, so the paper goes back onto the roll.

  5. Gently pull the end towards you. Never pull hard: that breaks the blade.

  6. Is the end creased or half printed? Cut it off straight with scissors. A crooked or creased end causes a jam again straight away.

  7. Put the ribbon back and close the cover.

  8. Feed the paper in again as described under "Paper or ribbon has run out", from step 11.


​

Won't the cover open because the power was off for a moment? Switch the printer off and on again. It then cuts the sheet into pieces and the cover opens.


​

Won't the paper come loose without pulling hard? Then stop and report it to us.


​

The printer pauses

After a lot of prints in a row, the print head cools down. Just wait: the printer carries on by itself.


​

Streaks on the photos

  • Never put paper or ribbon loose on a table: dust causes streaks.

  • Just changed the paper? Check whether the printer fed out the 3 blank sheets. If not, take the scrap tray out briefly and put it back.

  • Don't press on the cover or put anything on it while printing.

  • Pale photos or odd colours? Only use the paper and ribbon from our box.


​

Still not working?

If the printer still won't work, report it in your account under Reports or in the chat. If your party is today or tomorrow, we help you right away.


​

Read also

Did this answer your question?